Acnodes PCH 3582 User Manual

PCH3582/3782/3982 15/17/19 inch Atom Fanless Panel PC User Manual PCH3582/ 3782/3982: 15/17/19” Industrial Fanless Panel PC wi

Figure 1.3: Dimensions of PCH3982

1.3 Brief Description of PCH3X82 The fanless PCH3X82 is Atom D525 powered panel PC with a rich variety of functions and peripherals. PCH3X82 is

Chapter 2 Hardware Installation 2.1 Mainboard Specifications Figure 2.1: Mainboard Overview Figure 2.2: Mainboard Dimensions

Figure 2.3: Jumpers and Connectors Location-TOP Figure 2.4: Jumpers and Connectors Location- Bottom

Specifications Board Size 165mm x 115mm CPU Support Atom D525 /1.80GHz (onboard) Atom N455 /1.66GHz (onboard option） Chipset Atom D525 + ICH8M

Front I/O by 2x5-pin header Power on/off switch Reset switch Power LED status HDD LED status Buzzer Watchdog Timer External I/O port Tempe

2.2 Jumpers Setting and Connectors 1. JCLR_CMOS: (2.0mm Pitch 1x3 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset

Open ATX Power Mode Close Power Auto on (Default) 6. BAT: (1.25mm Pitch 1x2 box Pin Header) 3.0V Li battery is embedded to provide power for CMO

8. USB3: (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB ports via a dedicated USB cable, speed up to 480Mb/s. Signa

GPIO21 3 4 GPIO61 GPIO22 5 6 GPIO62 GPIO23 7 8 GPIO63 Ground 9 10 +5V 11. COM3: (2.0mm Pitch 1x4 box Pin Header),it provides selectable RS422/

Warning!_______________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in

COM2,COM3,COM4,COM5 Signal Name: Signal Name Pin# Pin# Signal Name DCD 1 2 RXD TXD 3 4 DTR Ground 5 6 DSR RTS 7 8 CTS RI 9 10 NC COM6 Signal Name

USB2.0 ports, speed up to 480Mb/s. Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A. If the external USB device current exceeds 1

19. CPU SCREW HOLES: Four screw holes for fixed CPU Cooler assemble. 20. COM1: (Type DB9),Rear serial port, standard DB9 serial port is

LVDS1_VDD3 3 5 6 LVDS1_VDD3 3 LADATAN0 7 8 NC LADATAP0 9 10 NC LADATAN1 11 12 NC LADATAP1 13 14 NC LADATAN2 15 16 NC LADATAP2 17 18 NC LACLKN 19 20

27. CN1: (2.5mm Pitch 1x2 box Pin Header), an onboard 5V output connector is reserved to provide power for IDE/SATA devices. Pin# Signal Name

Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation, the system will display the following s

Please select boot device： Hitachi HTS545016B9A300 USB: USB Hotplug FDD ↑and ↓ to move selection ENTER to select Boot device ESC to boot

System Date [Tue 01/01/2002] ESC Exit V02.68 © Copyright 1985-2009 American Mega trends , Inc. 3.3 System Overview BIOS SETUP UTILITY

3.4 Advanced Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Settings Configure CPU ← Select Sc

► Smbios Configuration ESC Exit ► USB Configuration V02.68 © Copyright 1985-2009 American Mega trends , Inc. 3.4.2 IDE Configuration BIOS S

Packing List Accessories (as ticked) included in this package are: □ AC power cable □ Driver & manual CD disc □ Other._ (please specify)

Hard Disk Write Protect: IDE Detect Time Out : [IDE] [RAID] [AHCI] [Disabled] [Enabled] [35] Options: [0,5,10,15,20,25,30,35] ATA(PI) 80Pin Ca

WatchDog Setting: [Disable] [RS485 Type] Options: [10sec,20sec,30sec,40sec,1min,2min,4min] 3.4.4 Hardware Health Configuration BIOS SETUP UTILITY

BIOS SETUP UTILITY Advanced AHCI Configuration While entering setup, BIOS auto detects the presence of IDE devices. This displays the status

[1.4]

[1.1] 3.4.8 PCI Express Configuration BIOS SETUP UTILITY Advanced PCI Express Configuration Enables/Disables PCI Express Device Relaxed Orde

Active State Power Management: [Disabled] [Enable] Extended Synch: [Auto] [Disabled] [Enable] 3.4.9 Smbios Configuration BIOS SETUP UTIL

USB Configuration Enables support for legacy USB.ATUO option disables legacy support if no USB devices are connected ← Select Screen ↑↓ Selec

Advanced USB Mass Storage Device Configuration Number of seconds POST waits for the USB mass storage device after start unit command ← Sele

IRQ4 [Available] F10 Save and Exit ESC Exit IRQ5 [Available] IRQ6 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] V02.68 © Cop

[Enable] OffBoard PCI/ISA IDE Card: Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. Auto:Works for m

Table of Contents Warning!…………………………………………………………………………….……..….2 Packing List...

3.6 Boot Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings Configure Settings During System Boot

[Force BIOS] [Keep Current] Bootup Num－Lock: Select Power-on state for Numlock. [On] [Off] PS/2 Mouse Support,: Select support for PS/2 Mouse. [A

3.7 Security Settings BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Security Settings Install or Change the password.

password. Type the password again and press Enter key. You may press Esckey to abandon password entry operation. To clear the password, just p

BIOS Setup. If the connected panel is not included in the parameter list, display problem will occur. In this case, Please do not change BIOS setup.

[PCIE/PCI] Internal Graphics Mode Select: [Enabled, 8MB] Video Function Configuration: BIOS SETUP UTILITY Chipset Video F

DVMT/FIXED Memory Size: [256MB] [128MB] [Maximum DVMT] Boot Display Device: [VBIOS-Default] [CRT] [LVDS] [CRT + LVDS] Flat Panel Type: [1024

F10 Save and Exit ESC Exit ► Video Function Configuration V02.68 © Copyright 1985-2009 American Mega trends , Inc. DRAM Frequency: [

DVMT/FIXED Memory [256MB] ← Select Screen ↑↓ Select Item +- Charge option F1 General Help F10 Save and Exit ESC Exit Boot

Panel Backlight Control: Note: Panel support PWM Function. 3.9 Exit Options [Level9] [Level0~15] BIOS SETUP UTILITY Main Advanced P

4.1 Chipset Driver.…………………………...…………………………………59 4.2 GMA 3150 VGA Chipset Driver..…...…...………………...…..62 4.3 Network adapter Driver……...

[Cancel] Discard Changes: Diacard changes? (F7 key can be used for this operation) [OK] [Cancel] Load Optimized Defaults: Load Optimized Defa

outportb(0x4E, 0x07); //LDN selection register 3.10.4 Read/write GPIO sequence 1. Enter the extended function mode 2. Select logic device number

outportb(0x4F, 0x08); //Select LDN=8, GPIO Port6 or outportb(0x4E, 0x07); //LDN selection register outportb(0x4F, 0x09); //Select LDN=9, GPIO Port2

out dx, al Example C code: outportb(0x4E, 0xE6); //GPIO I/O selection reg. outportb(0x4F, 0x0); //0 – normal, 1 – inverted outportb(0x4E, 0xE4);

Example C code: //Set GPO62 outportb(0x4E, 0xE5); //GPIO data reg. Outportb(0x4F, (inportb(0x4F)|0x4)); //Set Bit[2] //Clear GPO62 outportb(0x4E,

ENTERPRG //Select the logical device 9, GP2 SELETDEV(9) //Activate GP1 WRITEREG(0x30, (inportb(0x30)|0x2)) WRITEREG(0xE6, 0x0) WRITEREG(0xE4

//Start the super I/O chip programming ENTERPRG //Select the logical device 9, GP2 SELETDEV(9) //Read GPIO Value outportb(INDEXP, 0xE5); cGP2 =

InitGP6(); //Read GPIO Port 2 cGP = ReadGP2(); printf("\nRead GPIO Port 2 Status: %X", cGP); //Write GPIO Port 6 WriteGP6(cGP); pri

Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software a

4.1 Chipset Driver To install the chipset driver, please follow the steps below. Step 1. Access Industrial Panel PC. Select Chipset Atom D525 + ICH

Chapter 1 Getting Started 1.1 Specifications Model No. Specs PCH3582 PCH3782 PCH3982 System Processor Atom

Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to continue.

Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish then remove any installation media from the drives.

4.2 GMA 3150 VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1. Select GMA 3150 VGA Chip

Step 3. Click Next to continue setup program. Step 4. Read the license agreement. Click Yes to accept the license agreement.

Step 5. Click Next. Step 6. Click Next to continue.

Step 7. Select Yes, I want to restart this computer now. Click Finish then remove any installation media from the drivers.

4.3 Network Adapter Driver To install the Network adapter Driver, please follow the steps below. Step 1. Select Network Adapter. Step 2. Click N

Step 3. Read license agreement. Select I accept the terms in the license agreement then click Next to continue. Step 4. Select Drivers, PROSet

Step 5. Click Install to begin the installation. Step 6. Click Finish to compete the installation.

4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. Step 1. Select Rea

Mechanical Construction Stainless Steel Housing (APC-3X82) / Steel Housing (APC-3X83) IP Rating Front Panel IP65 / 6 sides IP42 with waterproof kit M

Step 3. Click Yes to continue the installation. Step 4. Wait for installation.

Step 5. Select Yes, I want to restart my computer now. then click OK.

Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your PenMount 6000 Controller

Step 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses RS232 interface, please plugged in before the machine

Step 4. Read the license Agreement. Click I agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows

Step 6. Wait for installation. Then click Next to continue. Step 7. Click OK.

Step 8. Click Finish to compete installation.

5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calib

Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this

Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points

1.2 Dimensions Figure 1.1: Dimensions of PCH3582

Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to c

Setting

About This panel displays information about the PenMount controller and driver version.

Multiple Monitors Multiple Monitors supports from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support M

Step 2. When the mapping screen message appears, click OK. Step 3. Touch each screen as it displays Please touch this monitor. Press „S‟ to s

the system understands where the displays are. 4. If you more monitor mapping one touch screen, Please press „S‟ to skip mapping step. Tools

About You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The PenMount monitor ic

PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP suppo

Figure 1.2: Dimensions of PCH3782