Acnodes PC 9150 User Manual

PC 9XX0 Industrial Panel PC User Manual PC 9XX0: 7 / 8 / 12 / 15” Industrial Panel PC with Dual-Core N2600 1.6GHz Processor

1.3 Brief Description of PC9XX0 SERIES There are 7”, 8”, 12”,15” Industrial Compact Size Panel PC in PC9XX0 series, which comes with flat f

Figure 1.7: Rear View of PC 9120/ PC 9150 1.4 Installation of HDD(PC9070/PC9080) Step 1 There are 2 screws to deal with

Step 3 Take out SSD Card bracket. Step 4. You can replace SSD card by unscrewing 4 screws as shown in the picture. Note: 4 screws are packed i

Step 6. Gently screw the screws. Installation of HDD(PC 9120 / PC 9150) Step 1 There are 2 screws to deal

Step 2 You c an put or remove HDD into the machine by pulling the HDD bracket. Step 3 You can remove HDD by unsc r

Chapter 2 Hardware 2.1 Mainboard Specifications Board Size 170mm x 113mm CPU Support Atom N2600 /1.60GHz Chipset NM10 Express Memory Support

4-bit digital Input 4-bit digital Output 4-bit digital I/O Pin header via CN3 2-bit digital Input 2-bit digital Output Battery Support CR2477 Li ba

(units :mm) Figure 2.1: Mainboard Dimensions

2.2 Installations SBC-7106 is a 4" industrial motherboard developed on the basis of Cedarview-M Processors and NM10, which provid

Board Bottom Figure 2.3: J umpers and Connec tors Loca tion_ Board Bottom 2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm P

PC 9XX0 Industrial Panel PC Warning! This equipment generates, uses and can radiate radio frequen cy en erg y and if not installed

3. BAT1 : (1.25mm Pitch 1X2 box Pin H eader) 3.0V Li battery is embedded to provide power for CMOS. Pin# Signal Name Pin1 VBAT PIN2 Ground

8. JP1: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port. JP1 Pin# Function Clos

11. COM1: (Type DB9 ),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. CO M1 port is

RS485 (option): Pin# Signal Name 1 NC 2 NC 3 485- 4 485+ 5 Ground 6 NC 7 NC 8 NC 9 NC BIOS Setup Advanced/W83627UHG Super IO Conf iguration/Serial

13. COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# Sign

23. LINE_OUT: (Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to provide high quality audio I/O ports. Line Out can

28. LED2: LED STATUS. Green LED f or Motherboard Standby Power Good statu s. 31. CN3: (1.27mm Pitch 2X30 Pin Header), For expand output con

3P3V_S5 57 58 3P3V_S5 12V 12V_S0 59 60 12V_S0 12V

3 BIOS Setup Description 3.1 Operations after POST Screen After CM OS discharge or BIOS flashing operation,.Press [Delete] k ey to enter CMO

3.2 BIOS SETUP UTILITY Press [Delete] key to enter BIOS S etup utility during P OST, and then a main menu containing system summ ary information

PC 9XX0 Industrial Panel PC Packing List Accessories (as tick ed) includ ed in th is package are: AC po wer cable Driv er & manual

System Lan gu age [English] System Date [Sun 01/01/2012] System Time [00:00:08] Access Level A dministrator : Select Screen : Select I

3.4 Advanced Settings Aptio Setup Utility – Copyright (C) 2012 Amer ican Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit

[Disabled] [Enabled] SERR# Generation: [Disabled] [Enabled] 3.4.2 ACPI Settings Enable ACPI Auto Conf: [Disabled] [Enabled] Enable Hibernation

L1 Cache RAM 2x56 k L2 Cache RAM 2x512 k Processor Core Dual Hyper-Threading Supported Hyper-Threading: [Enabled] [Disabled] Execute Di

[AH CI] Misc C onfiguration for hard disk 3.4.6 USB Configuration USB Configuration USB Devices: 1 Drive 1 keyboard Legacy USB Support: EH

[R S-485] [R S-422] Serial Port 2 C onf iguration Serial Port 3 C onf iguration UART Mode Selection [RS-485] [R S-422] Serial Port 4 C onf ig

Console Redirection Settings 3.4.10 PPM Configuration PPM Conf iguration EIST: CPU C state Report Enhanced C state CPU Hard C4E C PU C6 sta

3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2012 Ame rican Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit 

[1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.25GB] Intel IGD Configuration IGFX – Boot Type LCD Panel Type [VBIOS De

IGD Clock Source [External Clock] [Internal Clock ] Fixed Graphics Memory [128MB] [256MB] A LS Support [Disabled] [Enabled] B ack li

Table of Contents Wa rning !………………………………………………………………………… ….……..….2 Disc laimer………………………………………………………………….…………………2 Pa cking List………………………………………………………

3.5.2 S outh Bridge TP T Devices PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 DMI Link A

3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot

Fast B oot Skip VGA Skip USB Skip P S2 [E nabled] [E nabled] [Disabled] [E nabled] [Disabled] [Disabled] [Enabled] [Disabled] [Enabled

[Never] B oot option filter [UEFI and Legacy] [Legac y only] [UEFI only] Launch P XE OpROM poli [Do not Launch] [UEFI only] [Legac y onl

3.7 Security Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit

You will have dir ec t access to BIOS setup without typing any password after s ys tem reboot once the pas swor d is disabled. Onc e the passwo

3.8.1 North Bridge Configuration BIOS SETUP UTILITY Chipset North Bridge Chipset Configuration ENABLE: Allow Remapping of Over lapped PCI

[Enabled, 32MB] [Enabled, 128MB] Video Function Configuration: BIOS SETUP UTILITY Chipset Video Functio n Configuration Options Fixed Mod

[LVDS] [CRT + LVDS] Flat Panel Type: [1024x 768 18bit 1ch] [640x480 18bit 1ch] [800x600 18bit 1ch] [1280x800 18bit 1ch] [1366x768 18bit 1ch] [102

[BIA Enabled at Level3] [BIA Enabled at Level4] [BIA Enabled at Level5] 3.8.2 South Bridge Configuration: Aptio Setup Utility – Copyright (C)

5.1 .2 Installing S oftware (Pro jected Capacitive)...69 5.2 .1 Software Functions(Resistive Touch)...

Discard Ch anges and Reset Reset Without Savin g Reset without savin g? Save Changes Save Setu p Values Save configuration? Discard Ch ang

3.9 Exit Options BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Exit Options Exit system setup after saving the changes F1

Load Optimized D efaults: Load Optimized Defaults? (F9 key can be used for this operation) [O K] [Cancel] Load Fail-Safe Defaults: Load Fail-Safe

Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The softw

4.1 Chipset Driver To install the chipset driver, please f ollow the steps below. Step 1. Select Intel (R) Chipset NM10 Express f rom the list Step

Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue.

Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any ins tallation media from the drives.

4.2 Graphics Media Accelerator driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) V

Step 3. Select I agree. C lick Install. Step 4. C lick Continue Anyway.

Step 5. C lick Continue Anyway. Step 6. To restart the computer, click Yes.

Chapter 1 System 1.1 Specifications PC 9070 PC 9080 PC 9120 PC 9150 System CPU Atom Cedar View N2600 1.6GHz Dual Core Processors System Chips

4.3 Network Adapter To install the Network Adapter device driver, please follow the steps below. Step 1. Select Realtek RTL8111D Driver. Step 2.

Step 4. Click Finish to exist the wizard.

4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the R ealtek ALC662 HD Audio Codec Driver, please f ollow the steps below. Step 1. Se

Step 3. Click Yes, I want to restart my computer now . Click Finish to complete the installation.

Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work with

Step 2. Select Resisti ve Touch. Step 3. Click Next to continue.

Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount W

Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyw ay.

Step 8. Click Finish to complete ins tallation.

5.1.2 Installing Software (Projected Capacitive) Step 1. Insert the product CD, the screen below would appear. Click touch panel driver. Step 2. Se

P ower Power Input 9~36V DC Mechanical Construction Sliver aluminum front bezel and chassis IP Rating IP65 front panel Mounting Panel mounting, VES

Step 3. Click Next to continue. Step 4. Select I accept the terms of the license agreement. Click Next.

Step 5. Tic k Install RS232 interface driver. Click Next. Step 6. Select None. Click Next. Step 7. Click OK.

Step 8. Tic k Support Muti-Monitor System. Click Next. Step 9. Go to C:\Program Files\eGalaxTouch. Click Next.

Step 10. Click Next. Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next.

Step 12. Wait f or installation. Step 13. Click Yes to do 4 point calibration. 5.2.1 Software Functions(Resistive Touch) Upon rebooting, th

Devic e In this window, you can find out that how many devices be detected on your s ystem. Calibrate This function offers two ways to c alibrate

Command C alibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 poin

Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points

Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then

Setting

F igure 1.2: Dime nsions of PC9080 F igure 1.3: Dime nsions of PC9120

About This panel displays information about the PenMount controller and driver version .

Multiple Monitors Multiple Monitors support f rom two to six touch screen displays f or one s ystem. The PenMount drivers for Windows 2000/XP suppor

2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor”. Fo

6. “Touch this screen to start its calibration” appears on one of the screens . Touch the screen. 7. “Touch the red square” messages appe

PenMount Monitor has the following f unction PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display ro

5.2.2 Software Functions(Projected Capacitive) General In this window, you c an see there is USB Controller. Click OK to continue. Monitor Map

Setting Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click T

Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Tim

Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization pa

Display In this window, it shows the mode of display. Enable Multiple Monitors. Map to main display if system has onl y one display monitor Full Scre

Figure 1.4: Dimensions of PC9150

Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function.

Hardw are Saturn Hardware Configuration

About To display information about eGalaxTouch and its version.